top of page
HIGH QUALITY EQUIPMENT
61" BUSH HOG® HDE-4 ESTATE SERIES ZT MOWER
Bush Hog HDE2261 zero turn mower featuring a Kawasaki FS651V Engine and 61" cutting deck.
Features:
Robotically Welded 7GA Steel Deck.
ZT-3100™ Dual Transaxles from Hydro-Gear®
Electronic Control Module
Keyless Start/Stop
Soft Start PTO
Center-Mounted 8 Gallon Fuel Tank
Pin-Out Deck Height Selection
Features:
Robotically Welded 7GA Steel Deck.
ZT-3100™ Dual Transaxles from Hydro-Gear®
Electronic Control Module
Keyless Start/Stop
Soft Start PTO
Center-Mounted 8 Gallon Fuel Tank
Pin-Out Deck Height Selection
61" Bush Hog Zero Turn Mower
Bush Hog HDE2561 zero turn mower featuring a Kohler KT740 Engine wiht a 61" cutting deck.
Features:
Robotically Welded 7GA Steel Decks
ZT-3100™ Dual Transaxles from Hydro-Gear®
Electronic Control Module
Keyless Start/Stop
Soft Start PTO
Center-Mounted 8 Gallon Fuel Tank
Pin-Out Deck Height Selection
Features:
Robotically Welded 7GA Steel Decks
ZT-3100™ Dual Transaxles from Hydro-Gear®
Electronic Control Module
Keyless Start/Stop
Soft Start PTO
Center-Mounted 8 Gallon Fuel Tank
Pin-Out Deck Height Selection
Bush Hog HDTH 6' Finishing Mower
Turn your tractor into a lawn mowing machine with the new HDTH “Turf Hog” Finish Mowers from Bush Hog. These new Finish Mowers deliver superior grass cutting performance for your well-kept lawn. With models ranging from 5’-8’, our HDTH Finish Mowers help you save time spent cutting your lawn, and more time enjoying it. Built Bush Hog tough in Selma, AL, Bush Hog's new HDTH Finish Mowers are manufactured to the highest quality standards for durability and performance.
5' Bush Hog BH115 Rotary Cutter
The New BH100 Series picks up where the Razorback Series left off. Bush Hog®’s legendary durability and reliability is enhanced even further in the new light-duty BH100 Series. Bush Hog has taken their quality to a new level in the BH100 Series by robotically welding the entire cutter. All welding is performed on the underside of the deck giving these cutters a clean, sleek appearance. All welds are applied at the same temperature, angle, and duration to ensure consistency from start to finish. Additional enhancements include a stronger gearbox stand & tailwheel caster fork, optional front chain shielding, and optional Cat. 1 Quick Hitch. The economically priced BH100 Series allows customers to take control of pesky weeds, grass, and small brush up to 1” in diameter while experiencing legendary Bush Hog® performance. As thousands of satisfied customers can attest, if it doesn’t say Bush Hog®, it just won’t cut it!
Bush Hog RT60GR 5' Rotary Tiller
The gear driven “ROTO HOG” by Bush Hog® are built Bush Hog® tough for years of dependable service. Available in standard or reverse till, there is a model that will fit your application. In ground cover conditions, a reverse till model works best because the flow of material tends to cover the chopped groundcover for quicker decomposition. The standard six blades per flange on every model gives the maximum breakup of soil even in hard or packed conditions. The heavy duty gear drive alleviates worries about the durability of a chain drive in the same tough conditions. The “ROTO HOG” is the perfect tool for landscape work, seed beds, or any other application that requires that the soil be pulverized.
4' & 5' Hardee Box Blades
ES-48 Hardee Box Blade Features:
Fixed Rear Blade
Standard Duty CAT I Hitch 48" Rear Box Blade
330 lbs
3 Scarifiers
ES-60 Hardee Box Blade
Features:
Fixed Rear Blade
Standard Duty CAT I Hitch 60" Rear Box Blade
390 lbs
4 Scarifiers
Fixed Rear Blade
Standard Duty CAT I Hitch 48" Rear Box Blade
330 lbs
3 Scarifiers
ES-60 Hardee Box Blade
Features:
Fixed Rear Blade
Standard Duty CAT I Hitch 60" Rear Box Blade
390 lbs
4 Scarifiers
Cammond GS6 Road Grader
The Cammond Industrial Scrapers are designed similar to the compact grading scraper, but in a bigger, heavier frame. It is also designed to loosen and smooth surfaces. It will take down high spots and fill in low spots while moving dirt from right to left which makes it really handy on gravel driveways and even county roads.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Cammond GS7 Road Grader
The Cammond Industrial Scrapers are designed similar to the compact grading scraper, but in a bigger, heavier frame. It is also designed to loosen and smooth surfaces. It will take down high spots and fill in low spots while moving dirt from right to left which makes it really handy on gravel driveways and even county roads.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Cammond GSI8-SK Industrial Road Grader
The Cammond Industrial Scrapers are designed similar to the compact grading scraper, but in a bigger, heavier frame. It is also designed to loosen and smooth surfaces. It will take down high spots and fill in low spots while moving dirt from right to left which makes it really handy on gravel driveways and even county roads.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Cammond GSI8-SK Industrial Road Grader
The Cammond Industrial Scrapers are designed similar to the compact grading scraper, but in a bigger, heavier frame. It is also designed to loosen and smooth surfaces. It will take down high spots and fill in low spots while moving dirt from right to left which makes it really handy on gravel driveways and even county roads.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
Features:
Mast is 5/8" plate with 3" x 3" x 3/8" mast spacer.
Top link and draw ears are 3/4" plate.
Heat treated scarifier shanks with replaceable points.
Cutting edge bracket is adjustable with settings 1" to 1 1/2" below side panels (preset at 1/4")
Front cutting blade is designed to adjust lower than the rear blade to compensate for additional wear.
All welded units - no assembly required.
bottom of page